Stencil Cleaner System
- Product：Stencil Cleaner System
- Catalogue：Equipments
- Views：175733times
- Update：2013-03-26 14:35:20
- Call：+86-769-81664889
Stencil Cleaner main features:
1, and not electricity, there is no security risk
2, four filters, to ensure that the use of cleaning fluid loop to achieve a minimum of cleaning fluid loss
3, plus safety interlock machine completely sealed design to ensure production safety and environmental safety
4, a special rotating spray designed to ensure a comprehensive network of high-cleanliness steel
5, automatic drainage system, reduce labor intensity, saving time
6, a special small air vents designed to improve the working environment
7, cleaning pressure is adjustable, ensuring the stability of steel mesh tension
8, the cleaning frequency automatic counting, to facilitate the timely replacement of filters and cleaning fluid
9, the visual design of liquid, add liquid to facilitate a timely manner to ensure the normal operation of the machine
10, modular controller, easy maintenance
1, Dimension: 750 * 1000 * 1650 (L * W * H mm) +30 mm exhaust
2, gas supply pressure :0.4-0 .6 MPa
3, air consumption :400-700L / min
4, cleaning the smallest aperture: BGA: 0.1mm, qfp0.3mm, 0201, Flip chip/3mm printed plastic stencil / Semiconductor Silicon
5, cleaning time: Paste 3 - 5min, red plastic 4-6min, cleaning products and cleanliness because there will be all the difference.
6, drying time :4-8min
7, filter method: four filters, a filter box filter 20μm; two security filter 10μm; three cartridge filter 5μm; four cartridge filter 1μm.
8, the cleaning fluid type; IPA, water-based solvents, alcohol, acetone, etc.
9, a single cleaning amount: 0.12L/TIME, (water-based solvent 0.03/TIME)
10, storage tank capacity: 60L
11, the operation mode: a key to complete cleaning and drying
12, add liquid and the liquid discharge method: semi-automatic
13, the main supplies: filter element (replace one to three months, mainly depending on cleaning frequency may be)
14, machine component configuration: All imported famous brand products
15, the largest steel mesh Size: 736mmx736mmx40mm (MAX)
routine maintenance and maintenance:
|
Project
|
Cycle
|
Looks clean
|
Room cleaning house cleaning
|
Check the air pressure
|
Check the amount of solvent
|
Clear tank impurities
|
Replace the filter
|
|
Every day
|
●
|
●
|
●
|
|
|
Cleaning / week
|
|
|
Every week
|
|
|
|
|
●
|
Replacement / 6 months
|
|
Stencil Cleaner Before You Begin
1, the installation site
To ensure safety and prevent possible damage to equipment, equipment should be installed in place of the following environmental conditions: Keep away from fire and heat and air Air dry, well ventilated clean, clean flat surface without vibration
2, mounting hardware, energy and attention required
2.1, the gas source pressure 0.4-0.6MPa, flow 400-700L/Min.
2.2, gas source to take over diameter ¢ 12mm, to be equipped with a quick connector
2.3, the top of the device design ¢ 125mm exhaust port, to be independent of the wind pipe connected to the outdoors. When asked to take over less than two 90 degree turns, the length is less than 6M, whether Need to increase the force exhaust fan (exhaust speed of the device automatically 3M / S).
Note:
To ensure safe production, use, customer must ensure in particular that the following security measures in place. The resulting accident, the Company does not assume any responsibility for security: with energized equipment at least 3 meters away, away from fire and heat. You must connect the ground wire, and a separate ground, can not live with other equipment ground connection. Exhaust pipe and the equipment can not produce any heat source equipment connected exhaust pipe connection (such as SMT reflow, wave soldering, etc.).
3, the installation space
In order to facilitate equipment operation, maintenance, repair, replacement parts, leaving the device 1 m above the surrounding space.
Click to contact customer service
Call：+86-13360654218
